Rebuilding a Carburetor on a Snowblower



The carburetor controls the air and fuel mixture to the engine. If the engine won’t start or shut offs just after starting, then the carburetor could be the problem.

Visit us at:
https://www.searspartsdirect.com?sid=soc:youtube:rebuilding-the-carburetor-on-a-snowblower

Or call 1-800-437-1673 to speak with a parts specialist.

The video includes these parts. Look up your model to make sure you get the right parts for your snowblower.
Carburetor Rebuild Kit
https://www.searspartsdirect.com/part-number/951-12788A/0071/247.html?sid=soc:youtube:direct-part-link

Find parts for your snowblower at:
https://www.searspartsdirect.com/partsdirect/product-types/Snow-removal-equipment-Parts?sid=soc:youtube:snowblower-parts

Or click here to schedule an appointment with a repair technician. https://www.searshomeservices.com/repair#showall

Transcript:
Remove the mounting screws and pull the starter switch off the bracket. Let the starter switch hang by the electrical cord. Remove the key. Pull off the choke and throttle knobs. Remove the acorn nuts that secure the carburetor to the engine. Remove the muffler shroud mounting screws. Work the engine shroud off the carburetor mounting studs. Disconnect the primer hose and stop switch wires. Remove the engine shroud. Release the hose clamp and pull the fuel line off the carburetor. Slide the choke control plate off the carburetor mounting studs and disconnect the choke linkage from the control plate and carburetor. Disconnect the throttle rod return spring and remove the throttle rod from the carburetor. Slide the carburetor off the threaded mounting posts. Place the carburetor on a clean work surface. Remove the fuel bowl mounting nut. Pull off the carburetor fuel bowl and gasket. Slide the float pin out and remove the float and float valve. Unscrew the main jet. Dump the main jet and emulsion tube out of the central column. Remove the plastic throttle stop and then pry the plastic metering plug out of the carburetor. Spray carburetor cleaner into the carburetor body, fuel bowl and all of the small brass orifices in the carburetor. Wipe the carburetor and fuel bowl clean with a clean shop towel. Be sure that all the brass orifices are clear of debris and varnish. Warning: Never run a wire through any brass orifices to clear varnish or debris. Place the new emulsion tube in the central column with the flat end facing the carburetor bowl. Reinstall the new main jet in the central column and tighten. Push in the new metering plug until fully seated. Reinstall the throttle stop screw. Thread it in until the throttle stop screw protrudes out the other side about 1/16-inch. Insert the new spring on the new float valve and snap the new float valve into the new float. Attach the new float to the carburetor using the new mounting pin. Place the new bowl gasket in the channel on the carburetor body. Reinstall the bowl on the carburetor using the mounting nut. Tighten the bowl nut firmly. Install the inner carburetor gasket on the mounting posts. Slide the carburetor onto the 2 mounting posts. Reconnect the fuel hose to the carburetor and secure it using the hose clamp. Reattach the throttle rod and throttle rod return spring to the carburetor. Install the outer carburetor gasket. Reconnect the choke push rod to the carburetor choke lever. Reconnect the other end of the choke push rod to the choke control plate lever. Slide the choke control plate over the 2 mounting posts and install the gasket. Pull off the muffler shroud before reinstalling the engine shroud. Remove the belt cover mounting bolts and pull off the belt cover. Remove the bolts from the red chute support bracket and pull the support bracket forward, releasing the control rod from the 4-way control rod receiver. Remove the front muffler shroud mounting bolts. Release the wire control cables from the retainer clip and pull off the muffler shroud. Reconnect the stop switch wires. Reconnect the primer hose. Align the choke knob shaft and the 2 carburetor mounting posts with the openings on the engine shroud and work the engine shroud onto the engine. Make sure that the breather hose passes through the opening and lines up with the rocker cover breather hose fitting. Slide the breather hose over the rocker cover fitting and secure the hose with the clamp. Reinstall the 2 acorn nuts to secure the engine shroud to the engine. Slide the wire control cables into the retainer clip and position the muffler shroud on the engine. Reinstall the muffler shroud mounting bolts. Push the control rod back into the 4-way control rod receiver and line up the support bracket with the mounting holes. Reinstall the bolts in the red chute support bracket. Reinstall the belt cover using the mounting bolts. Reinstall the choke and throttle knobs. Position the electric starter switch on the switch bracket and reinstall the mounting screws. Reconnect the spark plug wire. Push the key into the slot.

source

(2)

8 thoughts on “Rebuilding a Carburetor on a Snowblower

  1. I'd like to buy a new carb instead of rebuilding it (my carb is from 2010). What is the part number for a new carb that will fit a Craftsman 247.888301 snowblower?

  2. When i prime 2x the gas on my snow blower, i seen gas leak…i opened up the cover thinking i have a broken gas line, which i did not….the gas came out from the opening of the carburator out of a small hole.Any ideas? Thank you.

Leave a Reply

Your email address will not be published. Required fields are marked *