How to adjust valves on an OHV Briggs



Someone asked me how to do this, hope it helps, I do have the intake and exhaust backwards at the first of the video I called intake the exhaust,on used motors I gap them the same, thanks!

source

(4)

2 Stroke Cylinder Installation Procedures and Concerns with the Piston Rings



This video demonstrates how to install a cylinder onto a 2-stroke piston. Special concerns when dealing with 2-stroke rings are addressed. This demonstration was filmed in the lab at Western Iowa Tech Community College Motorcycle and Powersports Technology Program. If you would like more info on the program feel free to contact the instructor @ 712-274-8733 ext 1204 or email shane.conley@witcc.edu or dirk.bak@witcc.edu

source

(1)

“PART 1” HONDA HRC216 BLADE CLUTCH REBUILD / HOW TO REMOVE A STUBBORN RUSTED ON CLUTCH COVER



BUY THE PARTS HERE TODAY TO FIX YOUR HONDA HRC216 COMMERCIAL MOWER!!

CLUTCH COVER
http://amzn.to/17n2agy

CLUTCH DISK
http://amzn.to/1fUiQO8

CLUTCH SPRING
http://amzn.to/16h8Ehm

SOMTIMES THE CLUTCH COVER IS A BEAR AND A HALF TO GET OFF / TRY THIS METHOD

source

(3)

STIHL BLOWER REPAIR / BR420 MAGNUM / DIAGNOSIS / TEARDOWN AND COMPLETE ENGINE RESEAL / IN 1080HD



MY ONLINE E-STORE
http://astore.amazon.com/youtubeco04c2-20

ECHO DIAGNOSTIC TOOL KIT
http://amzn.to/16oICdi

BR420 REBUILD KIT
http://amzn.to/17Hcxwq

AIR FILTER
http://amzn.to/18EwoL2

CRANK SHAFT SEALS
http://amzn.to/1e41hQc

STARTER ASSY
http://amzn.to/1agr5n8

CARB GASKETS
http://amzn.to/1agr7eN

CARBURETOR COMPLETE
http://amzn.to/1fKM4z1

THE BR420 IS IN IMO THE BEST GAS BLOWER ON PLANET EARTH HOWEVER THEY WILL REQUIRE MINOR SERVICE FROM TIME TO TIME….WATCH AS THE MM1 TEARS THIS ONE DOWN TO THE LAST SCREW AND REASEALS HER AND GETS HER RUNNING FOR ONE MORE SEASON

source

(2)

BRIGGS AND STRATTON CARBURETOR REPAIR / GAS SHOOTS OUT OF MUFFLER / CRANKCASE FULL OF GAS



IS GAS FLOODING YOUR CRANKCASE? IF SO ITS TIME TO REPLACE THE FAULTY NEEDLE AND SEAT IN THE CARBURETOR

source

(1)

How to rewind a starter rope and recoil rebuild on small engines and atv Honda Briggs



This video shows how to reassemble an ATV recoil starter. You will be given tips to help with winding and installing that pesky spring. The actual recoil is from a TRX200SX but the procedure is similar to multiple brands and models.
This demonstration was filmed in the lab at Western Iowa Tech Community College Motorcycle and Powersports Technology Program. If you would like more info on the program feel free to contact the instructor @ 712-274-8733 ext 1204 or email shane.conley@witcc.edu or dirk.bak@witcc.edu

source

(1)

Servicing/rebuild your starter motor



When most starters quit, they only need a clean-up of water or oil ingression and carbon dust deposits, their brushes and commutators are within specifications.
New starters cost hundreds $ and any parts could be hard to find. Servicing them with a bit of creativity could save you some money. Brushes could be somehow extended but the commutator segments have to be long enough. Brushes could be as short as 5.5mm not 55mm, my slip.
Do maintain electrical separation between the baseplate + housing + 2 bare wired brushes (ground side) and cable terminal + 2 insulated brushes + armature coil (battery positive terminal side).
Total service time on this starter: 1 hr

source

(1)

Motorcycle Bottom End Rebuild Part 3 (of 3) Final Assembly



Everything You Need To Rebuild Your Bottom End!
www.rockymountainatvmc.com/Sales/482/Motorcycle-Bottom-End-Rebuild?utm_source=Youtube&utm_medium=Bottomeendrebuildpart3&utm_content=Description&utm_campaign=Youtubevideos

How-to disassemble and rebuild the crankshaft and transmission on a modern 2-stroke motocross motorcycle or ATV engine. This is Part 3 of this 3 part engine rebuild series from Rocky Mountain ATV/MC. In this video we cover installing the transmission into the case halve and then applying gasket maker onto the sealing surfaces. Also installing the other case halve and sealing everything up finishing the crank and bearing replacement on this engine. Get all the parts and tools needed for this complete engine rebuild @ www.rockymountainatvmc.com!

Click Here For Part 1 (Flywheel, Stator & Clutch Removal)

Click Here For Part 2 (Splitting Cases, Crank & Transmission Removal, Crank & Bearing Installation)

Click Here To Subscribe To Our Channel!
http://www.youtube.com/channel/UCQSXoYEPBXNPSx1hWbO2WRQ?sub_confirmation=1

Shop All Tools And Accessories Here!
https://www.rockymountainatvmc.com/t/1655/Shop-Tools?utm_source=Youtube&utm_medium=BottomEndRebuild1of3&utm_campaign=Youtubevideos

source

(1)