Repairing a Governor on a 6.5HP Briggs Intek Motor



This video show how to adjust the governor on a 6.5 – 7 HP Briggs and Stratton motor.
Remember to do this only if you are qualified and I am not responsible for injury or worse if you attempt this.
If you enjoy, hit the LIKE button, COMMENT and SUBSCRIBE.

source

(0)

Briggs and Stratton INTEK OHV Engine: CARBURETOR REBUILD & Repair. Riding Lawnmower LEAKING GAS FIX



Jeff’s Little Engine Service shows you HOW TO remove, repair and rebuild a Briggs and Stratton 16.5 Horsepower INTEK OHV ENGINE WALBRO CARBURETOR. CARBURETOR LEAKING GAS: Float valve replaced and Fuel Inlet removed and replaced. SAME PROCEDURE FOR ALL MODEL INTEK OHV ENGINES!!!
Music by
Test Pilot – “Philadelphia”
Jeff is NOW Sponsored by GRIP tools! They help me help you! Check them out!
http://gripontools.net/
PLEASE KEEP IN MIND when you are watching my videos: I am showing you the least expensive, quickest “backyard” methods for repairing or servicing your lawnmower. Replacing all components such as gaskets and fuel lines is always recommended when rebuilding or repairing equipment. With these videos I hope you are able to fix and repair your lawnmower yourself with minimal parts, knowledge and tools. Thank you for watching!
Copyright 2016 Jeff’s Little Engine Service

Donations and tips are GREATLY appreciated!
click PayPal link below
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=DCJQ2QPAYL2TE

source

(2)

BRIGGS CARB REBUILD



Tools and supplies: http://astore.amazon.com/ldullc-20
My Landscaping Website: http://www.landdesigns.com/
My Chainsaw and Wood Splitting website: http://sawsandsplitters.com/

Working on my chipper shredder engine today. It has a 5 hp Briggs and Stratton Horizontal shaft motor. I’ll take you through the process of removing the carburetor, cleaning the carburetor and installing the carburetor back on the engine.

This video will help you avoid some of the common mistakes made as you watch me make them.

Good luck on your project!

Donyboy Showing the Linkage Configuration: https://www.youtube.com/watch?v=hK2sZjavTaw
Michael Lovely Showing how to Clean the Carburetor; https://www.youtube.com/watch?v=Dbfz7J2M0SE
sblg43 Showing the Linkage Configuration: https://www.youtube.com/watch?v=6q8WEp5qV0o

Words that may help you find this video:
Briggs ans Stratton Carburetor Rebuild
Briggs carb Rebuild
Briggs carb kit
Briggs carb parts

source

(2)

Briggs & Stratton 5500 watt 10 hp Generator Carburetor Repair



Briggs & Stratton 5500 watt 10 hp Generator Carburetor Repair
Cleaning the carb on my generator. After I got gas it started on the first pull…

Facebook: https://www.facebook.com/groups/1208129455864098/?ref=bookmarks
Twitter: @FloridaBoySurv1

generator,briggs,briggs and stratton,repair,carburetor,stratton,generator repair,briggs & stratton,power,engine,how to,generac,portable generator,and,gas,craftsman generator,electric generator (invention),watt,start,carb,honda,powermate,fix,howto,motor,coleman,diy,husqvarna,watts,craftsman,replace,FloridaBoy Bushcraft and Survival,shtf,hurricane prep,hurricane

source

(0)

Small Engine Repair: How to Check for Spark on a Tecumseh, Honda, Briggs & Stratton Lawn Mower



Visit http://www.thesmallengineshop.net

**Always follow the instructions in your repair manual when doing repair or maintenance work on Outdoor Power Equipment. Manuals can be found at the manufacturers website.**

Most people check for proper engine spark by removing the spark plug, attaching the plug wire and grounding the plug to the engine while spinning the engine over and looking for a spark to jump across the spark plug gap. This method is not always reliable. The amount of voltage needed to jump the spark gap set at .030″ with the plug removed from the engine is about 2000 volts. The amount of voltage required to jump the same plug gap with the plug installed in the engine and operating under operating conditions is about 8000 volts, so it is possible to see a spark with the plug removed, but not have a spark with the plug installed.

A more reliable method is to remove the spark plug wire cap, and hold the spark plug wire approximately 3/16″ away from the spark plug and spin the engine over. A good ignition system will produce a orange/blue spark from the end of the spark plug wire to the spark plug. The problem with this method is it is easy to get shocked and hard to turn the engine over while trying to hold the end of the plug wire 3/16″ away from the plug. The benefit of this method is it is more reliable then the first method and doesn’t require purchasing any special tools.

Another method for checking the ignition for proper spark is to purchase the Briggs & Stratton Spark Tester, part #19368. This tool can be used to check for spark with the plug removed and using no hands, so the engine is easy to spin over and there is no risk of being shocked. The tool can also be used to view the spark while the engine is running. This is very valuable when trying to diagnose a rough running engine or a engine with intermittent problems.

Thank You For Watching!

source

(6)

HOW TO TROUBLESHOOT a GENERATOR that WON’T START or RUN – BRIGGS and STRATTON 10 Horsepower engine



10 Horsepower BRIGGS and STRATTON Engine on a GENERATOR. A BLOWN HEAD GASKET is DAGNOSED and FIXED. Torque Specs and HEAD BOLT Tightening specifications, sequence and procedure.
music by my band BonZaiRod “Staging Lane”

source

(7)

Is it the VALVES? Single Cylinder Briggs and Stratton OHV VALVE ADJUSTMENT Procedure and Specs



Briggs and Stratton single Cylinder OHV. VALVE Adjustment Procedure. Tutorial. Jeff’s Little Engine Service demonstrates HOW TO Troubleshoot and Diagnose a 16 HP Briggs and Stratton OHV Engine. Model, motor models 31C707, 28700, 28P700, 28Q700, 28S700, 28U700, 28W700, 28770, 310700, 311700, 312700, 313700. How to ADJUST the VALVES on a 16 Horsepower Briggs and Stratton OHV overhead valve Engine single cylinder. VALVE ADJUSTMENT PROCEDURE Specifications specs. Is it the valves? VALVE PROBLEM on a Riding Lawnmower motor. HARD STARTING. Difficulty turning over. Too much compression. Trouble turning over? Same for many models Adjusting the valve lash valves Intek Craftsman Toro Troy-Bilt Poulan Snapper Sears Hayter Mountfield Lawnflite Snapper Yard Machines mtd ayp yardman yard man lawnboy Battery solenoid electrical problems. PLEASE KEEP IN MIND when you are watching my videos: I am showing you the least expensive, quickest “backyard” methods for repairing or servicing your lawnmower. Replacing all components such as gaskets and fuel lines is always recommended when rebuilding or repairing equipment. With these videos I hope you are able to fix and repair your lawnmower yourself with minimal parts, knowledge and tools. Thank you for watching!
Music by my band BonzaiRod
Copyright 2016 Jeff’s Little Engine Service
For T-Shirts and Parts, visit my website!
http://www.jeffslittleengineservice.com
Donations and tips are GREATLY appreciated!
click PayPal link below
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=DCJQ2QPAYL2TE

source

(4)